An Electrical Installation Condition Report and test in Leeds including about 30% of accessories removed for visual inspection will take at least 3 to 4 hours for and average 3 BED HOUSE. Then another 2 hours to fill in certification and report. Any one who says they will inspect 100% of accessories is most likely lying so will probably also be cutting corners on the testing. And anyone doing this work for less than £100 is NOT doing it properly. This work should cost about £180 - £200 for a sole trader or £220 - £300 for a larger company but will vary depending on how much time is needed on site. Basically as with most things in life, “you get what you pay for”. Unfortunately a lot of landlords just want ‘a piece of paper’ at the least cost. I'm afraid that with the advent of part 'P' and all these 'Testing specialist' companies springing up there are a lot of cowboys about. Stick to a registered person or company (you will then have comeback if a problem occurs) 

There is little point in setting up Regulations to control the way in which electrical installations are designed and installed if it is not verified that they have been followed. For example, the protection of installation users against the danger of fatal electric shock due to indirect contact is usually the low impedance of the earth-fault loop; unless this impedance is correctly measured. this safety cannot be confirmed. in this case the test cannot be carried out during installation, because part of the loop is made up of the supply system which is not connected until work is complete. 

In the event of an open circuit in a protective conductor, the whole of the earthed system could become live during the earth-fault loop test. The correct sequence of testing would prevent such a danger, but the tester must always be aware of the hazards applying to himself and to others due to his activities. Testing routines must take account of the dangers and be arranged to prevent them. Prominent notices should be displayed to indicate that no attempt should be made to use the installation whilst testing is in progress.

Faults

  • Domestic and Commercial
  • Faults/repairs
  • Light faults
  • Socket faults
  • Immersion heaters
  • Fuse board problems
  • Low voltage lights fault
  • Checks after flood
  • Fuses blown – tripping
  • RCD faults
  • 3 phase commercial circuit faults
  • Lamp replacement for offices and shops


The following tests are carried out:

  • Visual inspection of fittings
  • Continuity of earth conductors
  • Continuity of ring final conductors
  • Polarity
  • Installation resistance
  • Earth loop impedance
  • RCD test
Type of Installation

Maximum Period Between Inspection & Testing As Necessary

Domestic
- Change of Occupancy / 10 years 

Commercial 
- Change of Occupancy / 5 years 

Educational Establishments 
Residential
Offices
Shops
- 5 years 

Industrial 
- 3 years 

Places of Public Entertainment
Petrol Filling Stations
- 1 year 


Call us on 
0113 3909670  or  07864 000951

The testers used are:

  • Voltage tester to measure Volts
  • Continuity tester to measure ohms
  • Insulation resistance to measure Mohms
  • Earth loop impendence tester to measure ohms
  • RCD tester to measure mS

 


Also the supplies characteristics are tested to ensure a good earth and path of fault current is present. These tests are called Ze and PSC (Prospective Short Circuit). 

The readings are sent to our office from the engineer, verified by our manager and then typed up on fastest software, so you can be assured of a professional report. 

They are then sent out to you with a quote for any works needed to bring the property up to BS7671 regs, via post and also can be sent via email or fax if needed in a hurry.

Commercial Clients

Commercial Clients

Electricity at Work Regulations, Regulation 4(2) of the electricity at work regulations 1989 requires that; "As may be necessary to prevent danger, all systems shall be maintained so as to prevent danger" this statement applies to the fixed electrical installation as well as appliances of which is often misunderstood.


Landlords

Landlords have a legal duty to ensure the safety of tenants. This is regulated by several Acts of Parliament that impose a statutory duty on landlords with respect to electrical safety as follows:


  • The Consumer Protection Act 1987
  • The Health & Safety at Work etc Act 1974
  • The Electricity at Work Regulations 1989
  • The Landlord and Tenant Act 1985
  • Housing Act 1996
  • The Housing (Management of Houses in Multiple Occupation) Regulations 1990
Further Information For Landlords

The rules on electrical safety are less specific than for gas and furnishings when letting out property. The landlord is acting as a supplier of electrical equipment, including the electrical wiring in the property as well as any electrical appliances provided for tenants' use. Landlords have a legal duty to ensure that equipment is "safe". It is therefore recommended that appliances should be annually PAT tested (portable electrical appliance safety test) wiring of the flat or house should be checked at least every 5 years to obtain a Electrical Installation Condition Report. Although not mandatory BS7671 also suggests testing on change of occupancy.

Periodic Inspection & Test report (PIR) Domestic premises from £200.00. I had the pleasure recently of a landlord who was told his consumer unit had cables missing the main earth cores meaning no earth in the cables and none of his properties had Electrical Installation Condition Report Certificates to accompany them. The same properties were not in a satisfactory condition to start with hence the need for a inspection. The very same landlord also did not possess any gas safe certificates for his properties but saw fit to argue his corner reading a bit of text from a internet forum stating it was not mandatory to have properties tested for Electrical Safety as it meant he had to shell out money for his properties to be tested.

Here Are The Facts


If your property is electrically safe and you have a running maintenance record from the start having once had a clean bill of health from a Electrical Installation Condition Report and test in the first instance then fair enough, if not then how do you know it is Electrically Safe? 

Answer : You don't so do not play guess with peoples safety under the prehistoric opinion "its been ok up to press" or put cost above peoples safety like this Mickey Mouse Landlord did! 

You are governed by law as a landlord under the Electricity at work regulations as your property is supplying your customer with Electricity and this is where you can get in very serious trouble if something goes wrong.

PAT

(Portable Appliance Testing)

 

  • Specialist PAT testing carried out by qualified engineers
  • State of the art calibrated test equipment
  • Stickers provided on each appliance and a schedule of appliances tested, sent out on completion
  • Competitive rates, depending on amount of items
  • Schools; care homes; shops; cafes; restaurants; clubs; Domestic and Commercial;
  • DJ equipment

Pricing

Number Of Items - Price per item

 

49 or fewer

£3.00

 

50-249

£1.90

 

250-999

£1.50

 

1000 or more

Please call us for a quotation tailored to your needs

0113 3909670  or  07864 000951

The above pricing includes:


Thorough visual inspection | All required tests on our latest PAT testing equipment Pass and Fail labels | Certificate of testing | Fuse replacement (as required) Plug rewiring or new plugs (as required) with free retest

Sending your message.  Please wait...

Thanks for contacting us!  We'll get back to you shortly.

Thanks for online quotation!  We'll get back to you shortly.

There was a problem sending your message.  Please try again.